|
Fiber Optic Ethernet Communications  Media Converters MODEL LD3800 |
 |
| |
|
| |
MODEL LD3800 |
GbE SFP To 10/100/1000Base-T/GbE SFP Media Converter |
|
| |
 |
| |
LD3800 |
TECHNICAL SPECIFICATIONS |
- Model: LD3800
- Standard:
| IEEE 802.3 10Base-T |
| IEEE 802.3u 100Base-TX |
| IEEE 802.3z/ab 1000Base-T |
| IEEE 802.3x full-duplex flow control, |
| 1000Base-SX/LX |
- Connectors / Slot:
| P1 — RJ-45/SFP Slot* |
| P2 — SFP Slot (SFP is a must-have-option!) |
| [*Note:
Dual-Media Port-1 can only use either RJ-45 or SFP slot, but not both at the same time.] |
- Optional SFP Transceivers (Sold Separately):
| DX-SFP.3800 |
1000Base-SX Multi-Mode Duplex-LC, 850nm |
| DX-SFP.L10 |
1000Base-LX Single-Mode/10km Duplex-LC, 1310nm |
| DX-SFP.L40 |
1000Base-LX Single-Mode/40km Duplex-LC, 1310nm |
| DX-SFP.L70 |
1000Base-LX Single-Mode/70km Duplex-LC, 1550nm |
| DX-SFP.3L20 |
1000Base-LX Single-Mode/20km Simplex-LC, TX 1310nm |
| DX-SFP.5L20 |
1000Base-LX Single-Mode/20km Simplex-LC, TX 1550nm |
| [*Note:
Dual-Media Port-1 can only use either RJ-45 or SFP slot, but not both at the same time.] |
- Data Transfer Rate:
| 10/100/1000Mbps (auto-negotiation or forced mode) for TP |
| 1000Mbps for fiber |
- Handshaking: Not supported
- Duplex Mode:
| RS-232 |
n/a |
| RS-485 |
Half-duplex for 2-wire, Full-duplex for 4-wire |
- Cable / Max Distance:
| 50/125µm Multi-Mode fiber, up to 500m (400MHz-Km) or 550m (500MHz-Km) |
| 62.5/125µm Multi-Mode fiber, up to 220m (160MHz-Km) or 275m (200MHz-Km) |
| 9/125µm Single-Mode fiber, up to 10~50km (SFP Module dependent) |
| Category 5e or better UTP, up to 100m for 1000Base-T |
| Category 5 or better UTP, up to 100m for 100Base-TX |
| Category 3 or better UTP, up to 100m for 10Base-T |
- Duplex-Mode:
| Full-Duplex for 1000Base-SX/LX/T |
| Full-/Half-Duplex (auto-sense) for 10/100Base-TX |
- LEDs:
| Unit — PWR (Power) |
| P1 — SFP LNK/ACT (Link/Activity) |
| P1 — TP LNK/ACT (Link/Activity) |
| P1 — TP SPD (Speed for 10/100/1000Mbps) |
| [ Green for 1000Mbps, Amber for 100Mbps, OFF for 10Mbps ] |
| P2 — SFP LNK/ACT (Link/Activity) |
- Power Requirement: 0.9A up @ +5VDC
- Power Consumption: 3.6W
- Ambient Temperature: 0° to 40° C
- Humidity: 5% to 90%
- Dimensions: 140.7 x 87.7 x 29.4mm (H x W x D)
- Emission and Safety Regulations:
| FCC Part 15 Class A & CE Mark Approval |
|
|
|
ADDITIONAL FEATURES |
- Link Fault Pass-Through (LFP):
With LFP enabled (selectable by DIP-Switch at rear panel), if any segment cable(s) is/are broken, both ports in each converter will be turned OFF, i.e. no Link LED. If all segment cables are connected good, both ports in each converter will be turned ON, i.e. Link LED.
|
|
|
|
|
|
